Gifts for Men,Damaged Screw Extractor Set-Christmas Stocking Stuffers for Men Adults Him,Mens Gifts for Dad,Husband,Stripped Screws Nuts & Bolts Drill Bit Tools for Easy Removal of Rusty Broken Screw

Helped me out removing a stuck screw on my license plate holder. Use this to potentially loosen the screw and then a good set of pliers should be able to finish the rest.I was unable to get it to work with the second screw but honestly I think I drilled clockwise instead of anti-clockwise like it tells you to so I kind of messed up the whole so make sure you are drilling anti-clockwise so I still give it 5 stars

Why did you pick this product vs others?:I deal with stripped screws too much at work and have been really delayed because of them. I was very skeptical at first if this would really work. It not only really works, but works fast. I had 7 stripped screws today and this bit removed each screw in under 30 seconds. Without it I would have spent way too much time removing network equipment without damaging the network equipment I was removing. Best $8.00 I've spent.

The product met expectations, but I still can’t get over the fact that there’s a misspelling on the label.

I was installing some flag mounts. One of them needed to be adjustment. Of course it had stripped screws. Another just had two screws that stripped halfway down. I watched a couple of how to use on YouTube. Follow the instructions. By the way, all of the drilling and extracting is reverse spin. And I was able to complete my mission successfully. They do sell these much cheaper on TikTok, however, I question the quality. I did see one example on YouTube that showed a Dewalt breaking in the middle of The pre-drill. But these ones work for me.

This product is a must, the bolts we removed were stripped so bad, but they came out with ease using this thing. I don't usually write reviews, but I had to on this one. Great product!!!

I have an old Toyota Tacoma that I have been working on. I was removing one of the fenders when a small mounting screw head snapped off, leaving the remainder of the screw in the frame. I soaked the remaining bit of the screw and the hole with PB Blaster for a week, hitting it with spray at least once and sometimes twice a day.I felt like today was as good a day as any to try to get the screw out. I again soaked the remaining bits with PB Blaster, wiped away the excess, and attempted to sink the drill side of the #1 extractor bit into the screw. It spun, but had no impact. Not wanting to potentially snap off the bit, because I know how fragile they are, I switched to a left handed drill bit that was the same size as the #1 bit in the kit. After the hole was started and I saw that I was going in straight, I switched back to the drill side of the extractor bit and got it to sink into the hole, down to the stop on the bit collar. I flipped the bit over and attempted to extract.Using a drill on a slow speed, making sure not to put too much force behind it, I saw that the bit wasn't extracting, instead it was grinding away the metal stem of the screw. I applied slightly more pressure and saw that it was just grinding away more of the stem. I stopped with the #1 and switched to the #2 bit. This time to make sure that I wasn't going too fast, I used a 1/4 inch collar/guide on the bit and fit the other end of the guide onto an Allen wrench. Applying minimal pressure and turning about a quarter turn at a time, I finally got the #2 bit to bite. The bit was down inside the screw and decent amount. Since the #1 hadn't extracted and instead ground away some screw material, the #2 was seated really well in the screw body.Now with extractor seated and biting, hardly applying pressure, I pressed the allen wrench slightly to the left, and that's all she wrote.Now the extractor bit is buried in the screw, making the job infinitely harder since you can't drill through it.I read that a grinding bit in a dremel should be able to grind the extractor bit down and hopefully cause it to crumble. I just destroyed one grinder bit trying to get through it.Now I am looking at buying another "rescue bit" to remove the extractor bit that is broken off in the screw. I should have just left hand drilled the screw out as best I could. This thing is more of a headache than it's worth.

This is an amazing product. I had a vaccum with a stripped screw which i needed to remove to change the battery. I had been trying to remove it for a year. I even went to home depot and best buy without getting any help from those customer service reps. I decided to purchase the item hoping for the best and expecting the worst. This was the only product that was able to remove it! I am so relieved. Whoever that invented this product is a genius!

Why did you pick this product vs others?:I was trying to remove a large stainless steel bolt that had stripped. The drill bit end of the extractors was useless against stainless steel, but I bought a titanium left hand drill bit set and got the drilling done with them. The extractor work after I got the hole drilled. 3 rating is because the drill end of the extractors were useless in this situation.